Rod end bearing

Rod end bearing

Si5t/K Genuine Rod End Bearing for High-Load Wind Turbine Applications

Stop unexpected downtime in wind turbine pitch and yaw systems — the Si5T/K rod end bearing delivers consistent, low-noise articulation under extreme cyclic loads, even after 10,000+ oscillation cycles without relubrication. Built for OEMs who can’t afford field failures, it eliminates the risk of dry-start seizure thanks to its integrated PTFE-impregnated bronze liner — a detail engineers specify when steel-on-steel sliding contact must survive salt-laden coastal environments. SKF-certified rod end for wind power — genuine design compliance with ISO 20015 and SKF mounting torque specs Thin-film hydrodynamic lubrication optimized for ±15° oscillation at 0.1–0.5 Hz — no grease fittings needed Neutral packing + carton pallet shipping ensures zero contamination before installation 5 × 21 × 6 mm compact profile fits tight nacelle spaces without compromising load rating (C0 = 12.8 kN)

Inquiry View

Rod end bearing

POS22 Rod End Bearing – Self-Lubricating for Hydraulic Cylinders

Eliminate unplanned downtime and costly re-lubrication cycles in hydraulic cylinders — the POS22 rod end bearing delivers consistent, maintenance-free articulation even under shock loads and misalignment common in construction and forging applications. Self-lubricating PTFE-lined composite sleeve eliminates grease ports and scheduled maintenance — critical for sealed or hard-to-access cylinder rods M22×1.5 right-hand thread with 28mm thickness matches OEM mounting specs across major excavator and press manufacturers Radial spherical plain design handles ±15° angular misalignment without edge loading — a key reliability factor often overlooked in high-cycle automation equipment Dynamic load capacity of 37,400 N ensures longevity in high-frequency hydraulic actuation where standard rod ends fatigue prematurely

Inquiry View

Rod end bearing

SIR20ES SIKAC22M SIKB22F spherical plain bearing for hydraulic cylinders

Extend hydraulic cylinder service life and reduce unplanned downtime—even under high radial loads and frequent articulation. This spherical plain bearing delivers consistent, low-friction performance in demanding construction and industrial applications where misalignment and shock loading are routine. Engineered for precise 22×55×28mm mounting—matches OEM dimensional specs for seamless SIR20ES, SIKAC22M, and SIKB22F replacements Non-self-lubricating design allows full control over grease selection and re-lubrication intervals—critical for harsh environments like mining or outdoor hydraulics Bearing steel construction with whole outer ring ensures rigidity and load distribution integrity, especially during off-axis loading Available in P0–P2 precision grades and vibration classes Z1V1–Z3V3—so you get the exact tolerance and dynamic stability your application demands

Inquiry View

Rod end bearing

High-Quality Rod End Joint Bearing for Hydraulic Cylinders & Construction Machinery

Stop hydraulic cylinder misalignment and premature wear in high-cycle construction and forging applications — this rod end bearing delivers true spherical articulation under radial load, even with shaft deflection or mounting inaccuracies. Engineered to SKF-compatible P5 precision (not just P0) for repeatable angular performance in water conservancy and automation equipment Grease-lubricated with high-retention grease technology — eliminates dry-start failures common in intermittent-duty hydraulic systems Whole outer ring + 5mm wall thickness ensures rigidity under shock loads typical of excavators and forging presses Ready-to-ship SIK12F / SI12C / SIL1E variants — no waiting for custom lead times on critical spares

Inquiry View

Rod end bearing

POS28 Rod End Bearing – Self-Lubricating for Hydraulic Cylinders

Stop hydraulic cylinder downtime caused by lubrication failure or misalignment wear — the POS28 rod end bearing delivers consistent, maintenance-free articulation even under shock loads and extreme duty cycles. Built for engineers who specify components for forging presses and mobile construction machinery, it eliminates the need for relubrication ports, grease fittings, or scheduled maintenance intervals. Self-lubricating PTFE liner bonded to hardened bearing steel — no grease grooves or relubrication paths required Radial spherical plain design with 136mm overall length and M27×2 right-hand thread — matches OEM cylinder rod interfaces without adapters Dynamic load capacity of 58,400 N and static rating of 87,000 N — proven in high-cycle hydraulic applications where conventional rod ends fatigue prematurely Whole outer ring construction ensures precise angular misalignment compensation up to ±12° without edge loading

Inquiry View

Rod end bearing

Spherical Plain Bearing SIL15ES SIKAC16M SIKB16F for Hydraulic Cylinders

Stop hydraulic cylinder downtime before it starts — these spherical plain bearing sets deliver consistent radial load support and misalignment compensation in high-cycle construction and forging applications where standard bearings fatigue fast. Pre-loaded with high-stability grease (Z2V2 vibration rating) for extended service life without relubrication windows disrupting production 16×43×21mm specification matches OEM mounting envelopes — no redesign needed, just drop-in replacement for SIL15ES/ SIKAC16M/ SIKB16F legacy systems Bearing steel outer ring with 5mm wall thickness resists brinelling under shock loads typical in hydraulic ram reversals Rich stock + 100% on-time delivery means you get matched rod end pairs when your press line stops — not next week

Inquiry View

Rod end bearing

Hydraulic Cylinder Rod End Ball Joint Bearing for High-Load Industrial Applications

Stop hydraulic cylinder downtime before it starts — this spherical plain bearing delivers consistent, high-load articulation even under shock loads and misalignment common in wind turbine pitch systems and mining excavator booms. Self-lubricating steel-on-steel sliding contact eliminates grease relubing intervals — critical where access is hazardous or infrequent Thin-film hydrodynamic lubrication maintains film integrity at low speeds and high static loads, a known failure trigger in rod end joints 100×150×90 mm mounting envelope fits OEM replacement specs for SKF-compatible hydraulic cylinder rod end ball joint bearing applications OEM/ODM support includes custom bore geometry and surface hardening — we engineer the fit, not just supply the part

Inquiry View

Rod end bearing

High-Performance SI20TXE-2LS Rod End Bearing for Hydraulic Cylinders

Stop hydraulic cylinder downtime caused by premature rod end wear — the SI20TXE-2LS delivers consistent, high-angle articulation under heavy radial loads and shock cycling, even in dusty, high-vibration construction and forging environments. Engineered with a 5mm thick whole outer ring for superior edge load resistance — critical when misalignment exceeds 3° in compact hydraulic tie-rod assemblies Accepts standard grease or oil lubrication (no self-lubricating liner), giving you full control over maintenance intervals and compatibility with your existing fleet lubricants Available in P0–P2 precision grades and vibration classes Z1V1–Z3V3 — so you get exact fit and motion fidelity for OEM rebuilds or retrofit upgrades Stocked and shipped globally within 24h — backed by our ISO/TS-certified technical team for application validation before you order

Inquiry View

Rod end bearing

POS30 Rod End Bearing – Self-Lubricating for Hydraulic Cylinders & Construction Machinery

Stop downtime from lubrication failure in hydraulic cylinders and heavy-duty construction machinery — the POS30 rod end bearing delivers consistent, maintenance-free articulation even under shock loads and misalignment. Engineered for OEMs and plant engineers who demand reliability over replacement cycles, it eliminates grease ports and scheduled relubing without sacrificing radial load capacity. Self-lubricating PTFE-lined bore ensures smooth operation from –30°C to +120°C — no external lubrication needed, even after 500,000+ oscillation cycles Radial spherical plain design with M30×2 right-hand thread and 37mm thickness matches OEM mounting specs — drop-in replacement for SKF-compatible systems Dynamic load rating of 62,300 N and static rating of 92,200 N — verified per ISO 10326-1 for high-cycle hydraulic actuation Whole outer ring construction prevents edge loading in off-axis applications like excavator booms and forging press linkages

Inquiry View

Rod end bearing

Spherical Plain Bearing SI70ES SI80ES for Automation Equipment – Self-Lubricating

Eliminate unplanned downtime and lubrication maintenance in high-cycle automation equipment — the spherical plain bearing SI70ES SI80ES delivers consistent, low-noise articulation even under misalignment and shock loads. Engineered for robotic arms and precision motion systems, it’s built with a steel-on-steel sliding contact surface paired with a self-lubricating PTFE composite liner — no relubrication ports, no grease contamination risk, and zero maintenance intervals. Corrosion-resistant 70×49×92mm spherical joint fits directly into existing SKF-compatible robotic arm linkages Radial spherical plain bearing design handles ±15° angular misalignment without binding or edge loading Whole outer ring + rod end configuration ensures axial stability while allowing pure radial articulation Neutral packing on carton pallets enables seamless integration into your global supply chain

Inquiry View

Rod end bearing

Spherical Plain Bearing GE60ES-2RS for High-Load Radial Applications

Keep critical radial-load applications running longer under extreme stress—especially where misalignment, heavy shock loads, or maintenance access is limited. The spherical plain bearing GE60ES-2RS delivers proven performance in wind turbine pitch systems, mining conveyors, and steel mill roll stands—exactly where downtime costs six figures per hour. Self-lubricating steel-on-steel sliding contact eliminates grease relubrication intervals—critical for sealed or hard-to-reach assemblies Thin-film hydrodynamic lubrication maintains load capacity even during start-up/stall conditions (a known failure trigger in high-inertia systems) 100 × 150 × 90 mm dimensions match OEM mounting footprints—no redesign needed for retrofit or emergency replacement Backed by SKF-certified engineering support: application review, misalignment tolerance validation, and lifetime prediction modeling

Inquiry View

Rod end bearing

POS18 Rod End Bearing – Self-Lubricating for Hydraulic Cylinders

Stop downtime from hydraulic cylinder rod end failure — the POS18 rod end bearing delivers consistent, maintenance-free articulation even under shock loads and misalignment in construction and industrial machinery. Engineered for reliability where lubrication access is limited or impossible, it eliminates the risk of premature wear caused by missed greasing cycles — a common pain point in high-uptime operations like wind turbine pitch systems or mobile excavators. Self-lubricating PTFE-lined inner race — no relubrication needed for 50,000+ cycles under typical hydraulic cylinder loads Precisely ground M18×1.5 right-hand thread with 23mm radial thickness — matches OEM mounting envelopes without adapter spacers Dynamic load capacity of 25,700 N and static capacity of 30,200 N — certified for heavy-duty cyclic applications ISO-compliant spherical plain design (18×93×23 mm) with whole outer ring for maximum edge-load resistance

Inquiry View